You will notice the factory has implemented a minimum order to qualify for free shipping. You will find your free shipping is not 100% free (http://www.ultimaclub.us/buildHelp.asp#myExpImport) because of miscellaneous fees + import taxes but the factory doesn’t charge you for packing or the boat ride over so I am sure it’s still a huge savings. If you can swing it I recommend ordering everything with the *.

 

The real key is to order everything you can all at once or at least all the big items. Shipping the car over piece by piece will cost you thousands. For example when I had the brake kit sent over is was 350+ in shipping. The front splitter cost me more to ship than the splitter itself. When I asked the factory about shipping over the small windscreen they though it would be close to 1000 to ship. You get the point.

 

Can-Am USA PRICE LIST JANUARY 2007
Minimum Order* ($41408) includes free shipping

 

STAGE 1

 

LHD MIG welded round and square tube spaceframe chassis,
Fully bracketed to accept Chevrolet V8 engine and Porsche transaxle,
steering, fuel tanks, seat belts, pedals, radiator,
handbrake, gear linkage and brake servo mountings.
All powder coated in black satin finish.

$5162.00*

 

 

STAGE 2

 

Alloy panel kit in NS4 16swg aluminum sheet polythene
coated both sides for cockpit floor, sides and bulkheads,
pre-cut and bent including bonding adhesive, pop rivets
and skin pins.

$432.00*

 

 

STAGE 3

 

Lightweight fabricated TIG welded brake, clutch and throttle
pedal set, with adjustable foot pads. Including all bearings
fixing bolts nuts and washers.

$342.00*

 

 

Brake and clutch master cylinders, remote fluid reservoir
with float level, adjustable brake bias bar,
clutch clevis with all fixing nuts and washers.

$377.00*

 

 

STAGE 4

 

TIG welded wishbone set with urethane bushes and plated
fixing nuts bolts and washers.

$959.00*

 

 

Front suspension upper and lower ball joints.

$148.00*

 

 

STAGE 5

 

Rear uprights in LM25 heat treated alloy, fully machined
to accept Ford manufactured hubs, bearings and brakes.
Including all plated fixing bolts, nuts and washers.

$850.00*

 

 

Rear toe in adjusters including rose joints and fixing bolts.

$226.00*

 

 

Front uprights in LM25 heat treated alloy, fully machined
to accept Ford manufactured hubs, bearings and brakes.
Including steel steering arms.

$850.00*

 

 

STAGE 6

 

Front set of wheel hubs, wheel bearings, oil seals,
dust caps, hub nuts, washers and long wheel studs.

$418.00*

Rear set ditto.

$657.00*

Front set of 260mm vented disc brakes, calipers and pads.

$629.00*

(see accessories for other options)

 

Rear set of 260mm solid disc brakes, calipers and pads.

$456.00*

(see accessories for other options)

 

Handbrake lever, fixing bolts and pair of cables.

You need to decide if you want to upgrade the brakes to “AP Racing. $4009.00” under the Brakes section.

$173.00*

 

 

STAGE 7

 

Brake line kit in stainless steel pressure tested flexible pipe
with all fixing clips, washers and brake light switch.

$338.00*

 

 

STAGE 8

 

Steering column complete with universal joints, bearings
and fixing bolts.

$381.00*

 

 

Sports alloy steering rack with 2.5 turns lock to lock complete
with track rods, track rod ends, alloy mounting clamps,
fixing bolts and rack boot kit.

$860.00*

 

 

STAGE 9

 

Front mounted radiator and cooling kit comprising of five row
radiator, preformed alloy water pipes, twin fans with water
temperature sensor thermostat, alloy expansion tank,
alloy swirl pot and all fixing brackets.

$1295.00*

 

 

STAGE 10

 

G50 gear linkage in 20mm CDS including all needle roller universal
joints and chassis fixing rose joints. All plated.
Gear lever 1/2" rod.

$643.00*

Centre shift. Extra:

$264.00*

 

You will need to decide what type of trans you are using. If it's a cable shift or rod linkage. If it's a rod linkage I would opt for the Centre shift option, unless you want the shifter on the left side of the car. If you are going with a cable shifted Getrag transaxle you will probably want to order

“Gear change mechanism for Getrag transaxle including cables, actuator, Brackets, mounting plates, gear knob 6 speed with gaiter, GRP trim covers.            $1117.00”

Located in the cockpit section below.

 

STAGE 11

 

Foam filled alloy petrol tank with - 6 fittings, fixing kit, tube
type fuel gauge sender unit, aircraft type external flush filler
cap, alloy mounting, filler hose and clips. 40 liter capacity.

$814.00*

 

 

STAGE 12

 

Set of standard front and rear dampers with height and bump
adjustment. Coil spring poundage to suit proposed finished
weight of car including all fixing nuts bolts and washers.

$765.00*

You need to decide if you want to upgrade the shocks to

“Set of four top quality Intrax shockers fully adjustable for ride

height and bump complete with race quality road springs.           $1988.00” under the CHASSIS PARTS.

 

STAGE 13

 

Drive shaft pair with lobro universal joints and fixing bolts
Purpose made from high grade steel.

$1163.00*

If you are going for big horse power you may want to upgrade your drive shafts. Check out this thread for more info http://www.pistonheads.com/gassing/topic.asp?t=281250&f=20&h=0&hw=drive+shaft

 

STAGE 14

 

Wiring loom complete with fuse box, relay sockets and
multi connectors for separate front and rear looms.

$508.00*

 

 

STAGE 15

 

Can-Am bodywork in GRP with Isophthalic high heat
distortion resin comprising front and rear sections, side pods,
cockpit, doors, dashboard, headlight and instrument pods.
All in colored gelcoat.

$7341.00*

 

 

STAGE 16

 

Front and rear body hinges, door locks, door hinges, gas struts,
body securing latches and releases.

$906.00*

 

 

STAGE 17

 

Can-Am perspex wind deflector and side screens.
Can-Am perspex headlamp covers.

$998.00*

 

You are going to want to swap this out for the full windshield

“Can-Am laminated glass windscreen, frame and side screens.

 $1392.00”

The wind deflector is not street legal in the us. You could order both and swap in the defector after you get the car on the road.

$27995.00

 

 

Can-Am ACCESSORIES JANUARY 2007

 

CHASSIS PARTS

 

Roll bar comprising of a single hoop in 3.2mmx50mm
Cold drawn seamless tube with front braces to cockpit.

$851.00*

Alloy double skin kit for cockpit floor, radiator and rear bulkhead.

$333.00

Recommended for sound and heat insulation

Set of up-rated urethane suspension bushes with s/s sleeves. Recommended

 

$229.00

Gas strut kit for rear canopy. Recommended

$104.00

Set of four top quality Intrax shockers fully adjustable for ride
height and bump complete with race quality road springs.

$1988.00

This is a substitution for STAGE 12 if you feel you need the upgraded shocks

 

BODY

 

Remove and buff up all flash lines, cut out all apertures for lights,
trim all returns to correct size.

$987.00*

GT spec mid mounted rear wing in carbon fibre with adjustable flap
and carbon fibre skinned alloy honeycomb end plates.
If you want the rear wing now is the time to order it. It is huge and you don’t want to pay to ship it over later.

$2908.00

Set of body grills in black anodised expanded alloy.

$335.00*

Ultima electric door mirrors pair.

$518.00*

Sealed side luggage containers in 16g NS4 alloy pair. Recommended These get installed before the side pods go on.

$247.00

Luggage container covers in carbon fibre covered alloy honeycomb. Recommended

$212.00

Can-Am laminated glass windscreen, frame and side screens.
This is a substitution for STAGE 17. You need the full windshield to make the car street legal in the US. Some US members due like the wind deflector so you could order both and just swap on the deflector once you have gotten the car through what ever inspections your state requires.

$1392.00

Can-Am soft top hood, frame and high side screens.

$2908.00

Perspex headlight covers. If you didn’t order stage 17 you will need these.

$169.00

Helicopter vents pair.

$33.00*

 

 

BRAKES

 

Twin brake servos kit for 260mm standard brakes.

$619.00

 

 

Set of four 12.7" vented disc brake and callipers comprising X drilled
-320mm x 30mm AP Racing curved vane vented discs with alloy bells
and AP Racing four pot callipers (1.5" & 1.625" pistons with double seal)
with Mintex 1166 pads. Complete with billet fixing kit, all bolts and
AP brake fluid.
Most people upgrade stage 6 for these brakes

$4009.00

Pair of separate handbrake callipers for above with all
fixing brackets, bolts etc. You will need these with the upgraded brakes

$485.00

 

 

ENGINE BAY
Most of the parts for the engine bay will depend on what type of motor you are running. If you are running a sbc you could order a lot of these parts from the factory or you could order them in the US.

 

Twin fuel pump kit with stainless steel hose and all connections -

 

To suit Holley carb engines up to 375 bhp.

$458.00

To suit Holley carb engines up to 720 bhp.

$844.00

Petrol tank link in stainless hose.

$79.00

Braided stainless steel clutch pipe and fittings.

$115.00*

Accelerator cable kit with fixing brackets.

$65.00*

Exhaust system for small block Chevrolet TIG welded in stainless steel
comprising of 4 into 1 headers of 1.75" dia. with 3" collectors
and 3" tail pipes oval silencers with fitting kit.
If you are going to run a sbc this is probably your best bet. If your are going the LSX route these will not fit

$3104.00

Oil cooler kit comprising 25 row cooler, sandwich plate, pipework
in -10 stainless braided pipe with alloy fittings.
Can be purchased in the US, but you will have to fabricate your own mounting brackets + hose

$546.00

Accusump 6 pint capacity oil reserve electric valve, all fittings
braided stainless hose and alloy fittings in conjunction with oil cooler.
Can be purchased in the US, but you will have to fabricate your own mounting brackets + hose

$973.00

G50 transaxles- used from.
Can be purchased in the US.  Roger at www.phii.net is a great contact. You will need to determine what type of HP you want and get a box that can handle the power.

$2908.00

Getrag 6 speed Transaxles- used from.

$4000.00

Transaxle invert kit comprising mountings and breather kit.
You will need this part to mount the trans. There are 2 version of the G50 type boxes a short and a long. You need to order the one that fits your box.

$345.00

Engine/transaxle adapter - Chevy/Porsche. Including flywheel to fit small block
Chevy to a G50, needle roller spigot bearing and alloy housing.
They type of adapter will depend on what motor you are using. The LSX and sbc ones can be purchased in the US.  Roger at www.phii.net is a great contact. http://www.kennedyeng.com/ also sells them

$846.00

Engine/transaxle adapter Chevy/Getrag. Including flywheel to fit small block
Chevy to a Getrag, needle roller spigot bearing and alloy housing.

$1119.00

Clutch kit for G50 comprising cover, plate, thrust bearing and all bolts.

$872.00

Clutch kit for Getrag comprising cover, plate, thrust bearing and all bolts.

$696.00

Porsche starter ring gear.
Can be purchased in the US.  Roger at www.phii.net is a great contact.

$167.00

Starter motors gear reduction type.
Can be purchased in the US.  Roger at www.phii.net is a great contact.

$560.00

Speedo sensor.
Can be purchased in the US.  Roger at www.phii.net is a great contact.

$167.00

Extra Fuel tank complete. Recommended. Much easier to install before the side pods go one the car.

$814.00

Aluminum glass cloth canopy heat protection.
Heat shield can be purchased in the US.

$115.00

Silicon radiator and engine bay coolant hose kit. Recommended. Even if you are not running a sbc set up you can use most of these parts.

$217.00

 

 

COCKPIT

 

Steering wheel 320mm leather road.
Can be purchased in the US

$173.00

Steering wheel boss with deformable structure. Recommended

$67.00

Solid alloy gear knob (G50 rod linkage). Recommended

$38.00

Gear change mechanism for Getrag transaxle including cables, actuator,
Brackets, mounting plates, gear knob 6 speed with gaiter, GRP trim covers.

$1117.00

The factory supplied seats are very nice and worth the money, however there are several seats that will fit in an ultima and can be purchased in the US. Same is true for the seat belts.
Ultima seats are designed specifically to fit the Ultima with a minimum of
padding with the best of support and comfort whilst maintaining the
maximum use of space in the cockpit.

 

Ultima seat shells-pair.

$635.00

Ultima seats cloth covered - pair.

$934.00

Ultima seats Alcontara covered - pair.

$1276.00*

Ultima seats leather covered - pair.

$1392.00

Lumbar support (pneumatic) - pair.

$148.00*

Seat runners pair.

$99.00*

Seat belts six point fixing with twist buckle release 50mm wide pair
manufactured specifically for Ultima.

$458.00

Seat belts four point fixing with snap release pair.

$173.00

Heater kit with all hoses valves and brackets.

$377.00

Air conditioning kit including integral heater, compressor with
mounting bracket to suit small block Chevy, condenser, drier, all mounting
brackets, switches and swaged hoses.
If you are getting a gtr this is probably a must have, for the canam it a personal choice. The canam can run pretty hot but with some fresh air ducting ac is not really needed. If you are going to install AC it’s best to do it before you fit the dash.

$2312.00

 

 

ELECTRICS

 

Rear lights, Indicators, brake lights, side repeaters, rear fog and
number plate lights.

$538.00*

Triple headlight kit.

$737.00*

Relays and fuses.

$137.00*

Switches (rocker type).

$122.00*

Pantograph wiper and washer kit.

$427.00*

Battery cables kit with main cable and two earth straps.

$81.00*

Battery race quality sealed.
Can be purchased in the US, but you will have to fabricate your own mounting brackets.

$150.00

Battery fixing clamp.

$32.00

Instruments Ultima type, white faces. 200mph speedo, 7000rpm
tacho, oil pressure, water temperature, volt meter, gas gauge.
Can be purchased in the US

$1013.00

 

 

WHEELS
Can be purchased in the US.

 

13" x 18" & 9" x 18" split rim set in polished alloy with billet centres.

$3514.00*

All the above include sleeve nuts.

 

 

 

TYRES
Can be purchased in the US.

 

335/30/ZR/18 tires pair (to fit GTR/Can-Am rear only).

$1181.00

245/35/ZR/18 tires pair (to fit GTR/Can-Am front only).

$696.00